How to Cover Wood Paneling

Wood covering was at one time a mainstream divider covering for homes. Today, it can watch outdated, particularly if it’s extremely produced using plywooFor whatever length of time that your boards are in conventional condition, you can spare yourself the exertion of tearing them down. Paint them rather, or paper over them with a strong divider liner.

Image Source: Houzz

Getting Started


Investigate the covering for defects. In the event that the boards are not fit as a fiddle, they will keep on deteriorating under the covering. In the event that there is real mold or distorting, tear down the boards. In the event that a board is leaving far from the divider, nail it down ready.


Clean the boards. On the off chance that your boards are fairly clean, you can escape with water and gentle cleanser. Grimy dividers may require a business degreaser to set up the surface for paint, trailed by a careful water wash. Degreasers can be unsafe to skin and lungs, so take after name directions carefully.


Push the boards. In the event that the boards flex or discourage when pushed, filling the depressions between them isn’t suggest. This development will make the filling break after some time. You can paint over the boards without filling, however the furrows will even now be obvious


Pick an approach. You can either paint over your boards or hang wall liner over them. Divider liner is an additional strong backdrop that will cover yet not conceal the notches in your framing.


Painting Wood Panels


Prepare the area. Move all furniture well far from the framing, and cover the floor with drop fabric. Gloves and a face veil are suggested, particularly in case you’re working with a huge territory or in a live with poor ventilation. Check all item marks for security data. Ventilate the stay with open windows or fans.


Sand away the wrap up. Most framing has a polished complete, which should be roughened up for the preliminary. Scrape up the wood a little with a medium coarseness sandpaper, away tidy with a soggy material.

Image Source : BITDIGEST Design

  • Continuously wear a dust mask while sanding.


  • You can rub on a deglosser. This is speedier, however you’ll need to work one board at any given moment, preparing when the deglosser dries to the right consistency.Check item mark for points of interest.


  • In the event that you cleaned the boards with TSP, you may have the capacity to skirt this progression. An extra light sanding or deglossing is as yet a smart thought.


  • On the off chance that you don’t sand away the complete, you should utilize an oil-based preliminary rather, as this will be less demanding for the paint to stick to.


Apply groundwork. Coat the surface meagerly and equally with an oil-or latex-based groundwork. In the event that the roller can’t venture into the scores, prime them with a paintbrush. Let dry for the time prescribed on the name.


  • Some genuine wood boards will drain tar through the paint. Keep this with a stain blocking preliminary.


  • A tinted preliminary adds to the last shading.

Image Source : Wood Naturally

Fill grooves with drywall joint compound . Do this lone if your sheets are sufficiently inflexible to deal with this , and you need to shroud the section surface. Blend a standard drywall joint compound “mud” with a power blender or hand instrument. You can likewise purchase a pre-blended compound. Spread it over the sections in a thin layer with a putty cut, at that point let dry overnight. In the event that important and it more often than not is apply another thin coat or two, until the point that the compound is flush with the board surface. Give each coat a chance to dry overnight. After the last coat is dry, sand it down with a fine-grit sandpaper.


Fill in gaps and imprints. In the event that there are any gaps in your boards, fill them with spackle. On the off chance that you are filling the sections with joint compound, you may utilize it for these gaps also.


Paint the boards. Move on no less than two layers of paint, letting dry and sanding gently in the middle. Utilize a froth wipe roller to maintain a strategic distance from undesirable textures. Once you’re happy with the look, you’re done.


Covering with Wall Liner


Pick your divider liner. Divider liner, likewise sold as crossing over material, is an overwhelming obligation covering that stays level over the holes between boards without listing or rankling. Most divider liners are intended to have backdrop put over them, yet some are paintable. For most dividers in great condition, a mid-range review lining paper is a good choice.


  • Pre-stuck divider liners are the least demanding to use for a novice. On the off chance that you make them backdrop encounter, you may favor an unpasted form.


  • Designed divider liners are accessible, yet most are clear.



Set up the wood surface. Clean the wood surface and let dry. Most completes won’t meddle with bond, however check your item data to ensure. In the event that the wood is particularly gleaming, unpleasant up the complete with medium coarseness sandpaper.


Cut wall liner. Cut lengths of divider liner around 4 inches (10cm) longer than the width of your wall.These even strips are for the most part best, so the liner creases don’t wind up in the notches between boards.


For bizarrely shaped walls, design out how you will organize your divider liner so you can cover the wall with as few strips as could reasonably be expected.


Coat with cement. Pre-glued liners simply require water brushed onto the back to initiate the cement. For a non-glued liner, brush the strip liberally and uniformly with an uncommon liner glue, getting ideal to the edge. Overlap the paper accordion-style as you go so it’s anything but difficult to deal with. Ordinarily, you’ll have to give the cement splash access for around ten minutes.


Append your first strip. Hold the collapsed liner up against the edge of a divider, and unfold it a tiny bit at a time as you go. As you unfold, brush it set up with a wide backdrop brush, straightening it against the boards. When you achieve the last crease, pencil a line where it will hit the edge, cut along the line, at that point brush it set up


Cover whatever is left of the framing. Set up each strip a similar way, leaving a microscopic hole between strips to evade knocks from covering.



News Reporter
Born and raised in New Delhi, graduated from University of Delhi, Parisha Sharma is a brilliant professional with a flair of writing on areas like health, sports, technology and more. Parisha is best known for his creative blogs and articles on lifestyle, food and travel. With a very valuable experience in the industry, Parisha has marked his footprints as a renowned guest blogger in Delhi.

Leave a Reply

Your email address will not be published. Required fields are marked *